DISQUS

Jonathan Mead · 1 year ago

Those are some shiny ass shoes.

In the military, do they make you shine the entire thing, on the tongue, in between the laces, etc?

Ben Pratt · 1 year ago

Excellent! I've been dissatisfied with the polishing method I was taught. This is just what I needed!

Zane · 1 year ago

We don't even shine our shoes in the Army any more. With the switch from BDUs (Battle Dress Uniform) to ACUs (Army Combat Uniform) we no longer have black leather boots - but rather the tan "sand" boots. They needed the occasional brush off after a particularly muddy day of obstacle courses at Basic, but otherwise they are practically no-maintenence (just like the ACUs which are no-iron). So while the new boots are practical, they don't have nearly the character building effect of the spit-shined black boots.

Tim · 1 year ago

I never used a brush to shine my shoes when I was in the Navy. I only used cotton balls or a used t-shirt that had been relegated to shoe shine duty. But, hey, if it works.

Rickey Henderson · 1 year ago

Great write up--Rickey's personal habit always involved applying the polish with a soft cloth then buffing his shoes to a shine with the brush. Apparently Rickey had been doing it wrong.... Quite informative.

grapfx · 1 year ago

There are some shoe shining hacks that I learned over the twelve years in the Army. The whole high polish the toe and heel was and is a bit over-rated except for the old Airborne boots. I would even polish the whole boot, removing the laces and polishing the tongue and around the grommets. Then I would blacken the grommets with that nail polish type stuff and a black sharpie.

A bit of mop and glo on a cotton ball will give you a quick and real glossy shine. Shine the boots or shoes as best as you can, then dip a cotton ball in a bit of mop and glo, get it a bit damp and don't oversaturate and go over your boots, making little circles and they the boots will glow in the dark. Most shoe and boots have a waxy protective coating that will kill your shine.
Use some leather cleaner and rub it in with water. Let the boots totally dry and give your boots a good polish and brush shine. Then apply some waterproofing polish, let them dry and then another good brush shine. A good polish foundation is the key. Then do the water and cottonball method in the article.

A pair of my original issue basic training given boots lasted my whole career and were my "garrison boots." I remember the nights I would just sit on the floor and shine my boots for hours. It was kind of a zen moment for me when I did it.

Eric B. · 1 year ago

I was an ROTC cadet my first two years in university. The cadre and prior-E cadets made it clear that the whole shoe needed to be polished (we were always in Dress "B") so we wouldn't look like "boot recruits."

Just doing the heel and toe got my flightmates and I though the Cadet D/IG's in-ranks inspection. Leaving the rest of the shoe unpolished invited later talkings-to by wing staff or cadre.

Rubbing alcohol is a good polish stripper, which should be done every so oftern, particualry if the boots haven't been shined in a long time (dirt gets embedded into the polish.)

Chris Cree · 1 year ago

I had a Marine Corps room mate in flight school (I was Navy) who claimed that melting the polish with his lighter made for a better shine. I just figured his shine was better than mine because he worked so much harder at it.

Me, I was content with good enough.

Keith · 1 year ago

I spent 10 years in the military split 6-4 between the Army and the Air force respectively. While in the Army I was a tanker in the Cavalry and boy howdy if we only polished our toes and heels we were doing extra duty cause we failed the inspection...To top it off since we were in the CAV we wore boots (not shoes) with our Class A uniforms (yes sir the pants were bloused!). The saving grace in all of that is that because we were tankers in the CAV we were allowed to wear tanker boots. NO LACES, rather, straps of leather that wrapped around the boot to secure it to your foot. Bar none the absolute best boots I have ever worn (to include jump boots).

Well then I crossed over to the Air Force with my beautiful boots all nice and shiny and stood out like a sore thumb. The last year of my time in the AF I only polished my boots once a month, basically just keeping them clean was enough for an AF inspection.

Thanks for the trip down memory lane!

While in the Air Force I think I polished my boots once a month.

FingerSoup · 1 year ago

For a real high-gloss shine, All you need is a soft cloth and a can of Kiwi Shoe polish.

This also assumes you have rinsed off any caked on mud/dirt/salt from the shoe under cold water. hot water will melt your base coat of polish, causing you more trouble than it's worth. If the thread attaching the sole to the rest of the boot is the same colour (the "catwalk" of the boot), you can take an old toothbrush with polish on it, to scrub clean, and put a dull shine on them.

First, wrap part of the cloth around your index finger. Moisten the cloth at the fingertip a small amount (Do not soak the entire rag). Some people swear by spit, others by lukewarm water, still others by cold. Rub your cloth in the polish to acquire a small amount on the cloth. Do not dig divots in your polish, as it will create more surface area and cause it to dry out quicker thus ruining a good can of polish.

Apply the polish in small circles, in very small amounts. Usually when I shine my shoes, I work one piece at a time - toe, tongue, heel, Inside "Upper" and outside "upper" parts of the boot/shoe.

Continue buffing the boot/shoe by going over the entire shoe in small circles, with a light amount of pressure. breathe "hot air" onto the boot/shoe as if trying to fog a mirror. This adds a slight amount of moisture to the boot, and softens the outer layer of polish ever-so-slightly so that the smallest unseen cracks will be filled in to allow the shoe/boot to become perfectly smooth and shiny.

I never use a brush, because brushes will scratch and damage the base coat, and brushes tend to leave streaks and scratches.

I've seen some cock-eyed variants, and everyone I know has a different routine. I've seen some people put their boots in the freezer before shining. I've seen people doing a coat of alcohol instead of water every 10-20 coats, to lightly strip the outer layer of polish to clear the top layer of dirt (Not fully stripping the boot though). I've seen Cotton balls, Buffing with an old nylon free of burrs, Various polish additives such as "Glisten" as sold on US military bases. All methods do something to make the boots look better, but in the end, the most maintainable boots are the ones that are polished very simply, and only with polish.

The above-mentioned "burn shine" (passing a flame over the polish) is a quick way to lay a base coat, but great care is needed. Too much flame on a specific area can melt away too much of the polish making your shoe patchy. As well, this can cause your polish to become dry and brittle, and flake off as you polish. If you decide to burn shine - make sure you polish the boot normally, shortly after, in an attempt to add some moisture back to the polish to keep the cooked layer from flaking off.

I have also seen horror stories of what "quick-shine" tips can do to boots. Mop'n'Glo, or similar products tend to make a real polish less effective - Future layers of polish rub off. I've seen people try things to perma-shine their shoes such as placing Saran-wrap on the boot then melting it in an oven at low heat (saran wrap will get "run" in it like a stocking). Melting hard plastic such as plexiglass onto the boot (the polish shattered). Don't be stupid. Real men do the hard work required.

dave · 1 year ago

One thing I used to do was apply a thin coat of neutral polish after the black was nice and shiny. That gave them a good gloss. Oh, and nothing shines better than an old, brown t-shirt. ;)

Phil · 1 year ago

In the Navy (once we were in the fleet), a shoe shine consisted of rubbing the toes of your shoes on the back of your calf in formation, just before an inspection. It worked.

Muju · 1 year ago

I learned how to shine shoes from my Dad. When I was growing up I always watch him bring out all of our shoes and he would start cleaning and polishing them all.
His method is basically the same as above but instead of cotton balls he uses toothbrush.

Thanks Dad!

ahhhh · 1 year ago

While I don't recommend this for boots you care about, I needed a quick clean and shine on a pair of old boots one day, so I tried foaming tire cleaner followed by silicone tire dressing, each wiped off with paper towel. It worked so well that I ended up using that method from then on on those boots.

As a bonus, you could clean and shine the sides of the soles at the same time. You just had to be careful not to get the tire dressing on the tread area, because it made it a little too slippery.

Ronn Waters · 1 year ago

Wow, thank you for the flash back!
I was an Army Warrant Officer Candidate back in the '80s. As a WOC we got to polish the WHOLE boot to a high shine (including the tongue) , this included putting brasso on a Q-tip and shining the little nails on the bottom of our jump boots. Anything else would bring much disapproval from our training officers. Fun days indeed.
We also used to carry a knee-high nylon stocking to touch up if we needed to during the day. Once we got out of the WOC-school and started flight training we were allowed to use LINCOLN WAX (it was illegal in woc school). We would shine our boots the usual black glass look, then put a coat of BLUE Lincoln wax on and buff. The Blue wax would make your boots GLOW.
I still do this 20 years later.

Scott · 1 year ago

I enjoyed Phil's comment about the wiping of shoes on the back of the pants.
I remember wearing a pair of cloth 'Kung-Fu' shoes that I picked up in Hong Kong for the whole time we were underway. I even wore them for quaterdeck watch inport as long as it was a night watch.
I got a few looks from the zeros, but no more.

Just to share a memory.

Darryl · 1 year ago

Why on earth would you waste a perfectly good cup of water? when I had to polish my boots we used the old tried and true method of a SPIT SHINE! that's right my friends good ole spit and polish, and damn if those boots were nice and shiny!

charlie · 1 year ago

those little pantyhose-like foot covers they have at shoe stores? grab a handful of those and stretch one taut and buff with a sawing motion as fast as you can for a few minutes. the friction and pressure combine to make a little heat that really brings the shine out. i never used anything more than an old pair of socks cut up into rags, a can of kiwi, and some old pantyhose, and i rarely find shinier shoes.

glenn horlacher · 1 year ago

Clean the boot(s) thoroughly...throw away any Kiwi polish you have (it flakes) and buy some Lincoln stain wax shoe polish (USMC APPD. SER. NO. 428)...use an old white t-shirt and COLD water, or spit, whichever you prefer....a zippo lighter to burn the polish in (don't burn the polish in the can, burn it on the boot) and a pair of old black pantyhose to buff with.
13 years Navy, 6 years NG and Army, and I had some dang good looking boots.

glenn horlacher · 1 year ago

And oh, BTW, don't forget an old tooth brush to do the welts with. Man, I love the smell of Lincoln polish in the morning.....

glenn horlacher · 1 year ago

And oh, BTW, don't forget an old tooth brush to do the welts with. Man, I love the smell of Lincoln polish in the morning.....

aiden · 1 year ago

I know a lot of people swear by spit shining, but the enzymes in saliva can damage polish and make it a lot harder to get the desired effect.

Through a lot of trial and error, I've found that very hot water tends to give you a better shine as the polish goes on easier.

Cotton wool or a soft cloth, kiwi parade gloss, hot water, very small circles and a lot of time and effort.

Adam · 1 year ago

Spit shining is 100% the best way in my opinion. I've been shining boots in the military for years now, and swear by it.

On the topic of what parts to shine, there has to be a "distinct line between the toe/heel and the rest of the boot" or the entire boot must be shiny. I give the entire boot a light shine with just a brush, then focus on the toe and heal for the spit shine. That keeps the entire boot nice, but saves a lot of time.

For low quarters, I shine the entire thing to keep them looking real nice.

To get a very distinct line for the toe and boot, you can hold a piece of paper down tightly to get a crisp line. Some people use tape but it peels more polish off under it.

Zendad · 1 year ago

My way:
paper towel and Armourall
Works well on the car dash its good enough for my boots!
Zendad
http://www.zendad.net

Ben Hovinga · 1 year ago

When I was in air cadets (151 Chadburn) I became a member of the "Royal Order of the Glassy Boot" and also received a certificate to prove. But to get this I didn't do any of what you just said and I had a better shine then that last image, all over the boot, not just the toe.

Mark · 1 year ago

I was a drill seargeant for 12 years. Bag the cotton balls and water and use a nylon panty hose footie to buff the wax. This is also good for spot cleaning on the trail, too.


Mark

Brian · 1 year ago

Spit and polish (or water and polish).

Simplicity is the hallmark of the spit and polish method. Everything else is a waste of time and money.

And trust the Drill Sergeants. Their boots always looked good.

Bjorn Nitmo · 1 year ago

You'll think I'm yanking your chain but I assure that I'm not when I say that an excellent and easy way to shine your shoes is with a banana peel. It's an old trick and it works like a charm.

Tom in Raleigh · 1 year ago

This is a great post, not just for the shoeshine tips, but for the great military stories. As one who didn't serve, I gotta admire the ones who did, and I love all the great stories. Thanks, y'all.

Jeff · 1 year ago

I agree with FingerSoup. After several years in military school (which from a shoe-shining perspective is a little more rigorous than the regular military), all you need is the can of polish, an old white t-shirt cut into strips and a little water.

I follow FS's method almost to the letter (including the hot breath) - except that I go through a process of softening the can of polish (using fingers wrapped in t-shirt, I mush the entire can so the whole thing is soft... adding in a few drops of water). I also use shoe-trees during the polishing (and remove them shortly thereafter).

I polish the entire shoe (though these days, I don't go for the tongue and take out the laces like I used to). Moving from a new pair of shoes to completely "glassed" (100% mirror shine all the way around) takes about 2 hours and about 3-5 layers of polish.

But the results are worth it. People ask me all the time where I get my shoes shined. When I tell them I do it myself, not only does the pride feel good, they're impressed, too.

Oh, for boots, the trick for the upper part of the boot is an old can of tennis balls. Put the can down into the boot to help it keep its shape during the polishing.

dan · 1 year ago

the shiniest shoes i've gotten is when i've had my shoes shined by someone. when alone, it's kind of hard to buff out a good shine using the above mentioned "sawing" motion.

Marcus · 1 year ago

Was in the South African army for a while. During basic training we had to polish/wipe our shoes before breakfast, after breakfast, before tea, after tea and so on.. as walking from one end of the base to another would get our shoes dusty etc.

To add to the methods above, we sometimes resorted to a cigarette lighter and deodorant can to "seal" the polish nicely on our boots.

Still polish shoes regularly, though not as extremely, and feel far more ready and professional for a hard day at work with polished shoes.

(and I've found that women always notice polished shoes.)

lostinid · 1 year ago

Great comparisons and stories. Especially liked the blowtorch (that is what a cigarette lighter and deodorant can do, right?) for burning the polish.

Since there's all this expertise here, has anyone got recommendations for repairing damaged/scuffed leather on a dress shoe's toe? I've recently bought what I thought were nice shoes, but they seem to be made out of the crappiest/softest of leather -- I've damaged 'em even just sitting at a desk (presumably, tucking my toes under my chair).

I can polish these to a degree, but the damaged leather isn't quite as smooth as originally, so I'm wondering what tricks or techniques are tried and true. Thanks in advance

Paul Edwards · 1 year ago

I am an ex guards man. I servered in the Household cavalry mounted regiment in London from 1971 to 1980.(The Lifeguards) I did public duties which involved mounting guard at Horseguards whitehall, state occasions and trooping the colour.

After that I went to work for the Adjutant of the regiment looking after all his kit I also worked for Earl Mountbatton when he was alive - for a short time.

The guards have a couple of differant techniques for 'Bulling boots' - and shoes. Drill boots ARE waxed with beeswax and loads of polish and ignited! (Dont try this at home!) Blown out and imeadietly smeared in lots of kiwi polish before they could get cold. They would then be given a good brushing - including the welts (important, If you didnt clean your welts you WOULD get charged!) after that the 'Bulling' would begin. using either a yellow 'diddly' (yellow duster) or a jewelers Sylvet (BEST WAY, Worth buying) IF you use a yellow duster make sure you wash it out completely to get out all yellow die, or it will leave nothign but smears!

Done properly they WILL look like BLACK DIAMONDS!!! - With ordinary shoes - smoother the better, prefer real leather - Start by using a fair amount of polish (NO WAXING!) Use either the yellow diddly or the sylvyte and use water ONLY - spit can leave a lot of smears once again.

Go round in circles but also 'pad' up and down the shoe aswell to get as much of a layer of pollish and shine on as possible. The is the way the queens guards prepare their thiegh high 'jack boots' for guard. They then start doing small circles polish water polish ALL OVER THE SHOE INC HEELS TO GET THE FINAL SHINE!

My last 3 years was spent at the Guards Depot in Surrey where all the seven regiments of guards are trained.

During the last few days of my service with the regiment before leaving in Sept 1980 The Regimental Drill Sergeant of the Irish Guards came and humbly asked me for my drill boots - one of the best pairs he had ever seen.....

P Edwards

Ex Lifeguards.

Joe Livaudais · 1 year ago

Good write up. I was pleased to see no mention of lighting the polish on fire or any other weirdness. The only thing I would add to the article is this:
After giving the shoe/boot the overall brushing (and before doing the toe and heel in the author's example) use a old t-shirt (or that sock that has a hole in it) and lightly wipe/buff the shoe. This will get the loose polish of the shoe and reduce the amount that will rub-off on clothing and other surfaces. You can also put freshly polished shoes in old socks for transport in duffel bags, luggage, etc.

Ed · 1 year ago

Make sure you break the boots in first before adding a lot of polish, otherwise, the polish will crack and flake off when you walk. You can do this quickly-ish by getting the boots soaking wet first and wearing them around for a while until they form to your feet and the way your feet flex. This is only important if you polish the whole shoe. Don't polish them until completely dry.
Use clear nail polish in the seam between the sole and the upper which is difficult to polish. - Permanent be careful.
To get a deep shine you need to get a heavy base of polish on the surface. It takes time to build up properly. - Unless you cheat.(heh heh FIRE!)
Don't rub to hard when you are buffing. You can rub the polish off. Be gentle.
If you use a t-shirt or cloth for buffing make sure it is 100% cotton for best results. Synthetics leave scratches.
Use water, not spit. Spit smears and gives cloudy results.

Paul Edwards · 1 year ago

...further to my previous post you may be interested to know that all members of the Household Cavalry mounted regiment in London use ladies tights to buff up thier non bulled leather work (horses headkits saddlery ext) works very well on all polishwork - esp to give extra shine to ordinary brush pollished boots and shoes.

- make sure you ask your partner fist though!!!!

P Edwards

(Ex Lifeguards)

Virilitas · 1 year ago

It was interesting to compare all of the shoe-shining-method descriptions inspired by this article. I am going to go test them out and see if the ladies notice. ;)

Andy · 1 year ago

As above, melting the wax/polish really helps - back in my basic training days, we'd use the lid off the polish to melt in with a zippo.

Also well worth a mention is that brown shoe polish gives a VERY deep shine on top of black (believe it or not!)

Paul Edwards · 1 year ago

..Yes, there is no doubt that a good set of well fitting shoe or boot trees really helps, makes the whole shoe into a hard surface to work on.

In the uK at least officers boots and shoes - esp if hand made which most of them are - always come with 'trees' You can buy them and the solid wood ones are best - try to avoid the cheepo plastic ones!!!

Bailey Hadley · 1 year ago

I am surprised that your instructions on boot and shoe clean-up and polishing do not include the use of oilve oil, a natural which does not leave the odor of shoe wax, while at the same time also nourishes the leather.

geof · 1 year ago

i've found that mirror-polishing my toecaps is both a useful and calming enterprise the night before job interviews and weddings and so forth, partly because so few people can/would do it.

John Williams · 1 year ago

Thank you so much for this Love you

John · 1 year ago

I'm surprised no cops have commented on their academy experiences yet! Just like being in the military, instructors at my academy held us to the highest standard of shoe shininess. Woe betide if you couldn't see your own face in your boots.

Chrissy · 1 year ago

I'm a Sheriff's Deputy, and I'm surprised that my department isn't very strict on shiny boots (except for our academy...even then...not so strict). I think I'm going to go shine my boots.

Tom · 1 year ago

Just to add to the already overwhelming amount of personal tips...

I used cotton wool balls for ages until I discovered make up removal pads (the little flat round ones). You can wrap them around your finger for much better control, stand less chance of scratching the polish with a fingernail, and don't leave little bits of cotton behind if you're a little careless. Definitely a winner in my book!

Also, as a personal thing, I tended to use more and more water the more layers i put on, until the final couple of layers (if you can call it that) were just water. I think this just gives a nice smooth sheen to the finish. I'm not for any of this fancy fire/melting/other nonsense

Dave Dragon · 1 year ago

The very last time I shined shoes was the night before I left the US Army.

I was mustering out as it was called and reported in uniform looking high & tight.

That was Nov 16 1978 and I haven't shined a shoe since.

Ride it like you stole it

William Chen · 1 year ago

Does Spit shining and *Burning your shoes work(you Know what i mean if your in cadets)

tradewe · 1 year ago

Thank you!

Winston · 1 year ago

Mop & Glo (or any floor wax-type material) is the **WORST** thing you can do to the boots. It looks great... until you put the boot on and the leather flexes and the hard acrylic layer shatters and flakes.

Roger B. · 1 year ago

I have a black pair of shoes, but the stitching is white. How do I keep the leather polished and the stitches white?

Thanks in advance.

Justin · 1 year ago

Exactly what kind of boots are those and where can you get them?

Q · 1 year ago

@Roger B. - I would recommend one of two ways to keep your stitching white. Before you start applying the black polish to your boots, use a thin layer of neutral polish to cover the white stitching. I will prevent the black polish from discoloring the lighter stitching.

The other method I would recommend is using a white grease pencil to color over the stitching should it get black polish adhered to it or if the stitching is starting to look dingy.

There is one other thing you can do, take your time. If you really slow down and pay close attention to where you are applying the polish and how you are buffing it out, you can and will avoid getting any polish on your stitching.

Hope that helps!

Rob Philip · 1 year ago

Wow. I'm really glad I never have need for shining shoes. Now that I think about it, I don't have any black shoes. I don't think I've ever spent 45 minutes on any aspect of getting clothing ready, even 30 years ago when I had a job that required a suit and tie every day.

Culver Eagle · 1 year ago

I go to military school and the only people who have to shine the whole shoe are the color guards but they're also not allowed to have state shines on campus. The "normal way" is to use a t shirt that is old. then Put a little water in the cap and soak the t shirt after pulling it tight around your finger. swirl your finger in the polish lightly and then make small circles all the way around. then soak in water again and run over the fresh polish then soak again and run the wet rag over the polished areas. after going all the way around where you want to polish then its time to buff. A little secret- ask your girlfriend, wife, mom, sister, anyone you feel comfortable asking, for an old pair of pantyhose. It must have been used!!!! also make sure they know it will be unwearable before you use it. the pantyhose makes a great buffing rag. if you want a really high gloss put a thin coat of brown polish on and buff in the same way. It really gets a good gleam.

David · 1 year ago

This gentleman has it EXACTLY right! When I was in the 82d Airborne (back in the BDU and jump boots days), we needed a high shine on those 'ol Cochorans. The brush actually makes it a bit harder (roughing up your wax surface a bit) and you'll never get the same shine. The old t-shirt (or cloth baby diaper if you can still find 'em) works great. The cotton balls are best after you get a good smooth base, but you can get 'em looking like glass without them.

Good article!

Originally Posted By FingerSoupFor a real high-gloss shine, All you need is a soft cloth and a can of Kiwi Shoe polish.

This also assumes you have rinsed off any caked on mud/dirt/salt from the shoe under cold water. hot water will melt your base coat of polish, causing you more trouble than it's worth. If the thread attaching the sole to the rest of the boot is the same colour (the "catwalk" of the boot), you can take an old toothbrush with polish on it, to scrub clean, and put a dull shine on them.

First, wrap part of the cloth around your index finger. Moisten the cloth at the fingertip a small amount (Do not soak the entire rag). Some people swear by spit, others by lukewarm water, still others by cold. Rub your cloth in the polish to acquire a small amount on the cloth. Do not dig divots in your polish, as it will create more surface area and cause it to dry out quicker thus ruining a good can of polish.

Apply the polish in small circles, in very small amounts. Usually when I shine my shoes, I work one piece at a time - toe, tongue, heel, Inside "Upper" and outside "upper" parts of the boot/shoe.

Continue buffing the boot/shoe by going over the entire shoe in small circles, with a light amount of pressure. breathe "hot air" onto the boot/shoe as if trying to fog a mirror. This adds a slight amount of moisture to the boot, and softens the outer layer of polish ever-so-slightly so that the smallest unseen cracks will be filled in to allow the shoe/boot to become perfectly smooth and shiny.

I never use a brush, because brushes will scratch and damage the base coat, and brushes tend to leave streaks and scratches.

I've seen some cock-eyed variants, and everyone I know has a different routine. I've seen some people put their boots in the freezer before shining. I've seen people doing a coat of alcohol instead of water every 10-20 coats, to lightly strip the outer layer of polish to clear the top layer of dirt (Not fully stripping the boot though). I've seen Cotton balls, Buffing with an old nylon free of burrs, Various polish additives such as "Glisten" as sold on US military bases. All methods do something to make the boots look better, but in the end, the most maintainable boots are the ones that are polished very simply, and only with polish.

The above-mentioned "burn shine" (passing a flame over the polish) is a quick way to lay a base coat, but great care is needed. Too much flame on a specific area can melt away too much of the polish making your shoe patchy. As well, this can cause your polish to become dry and brittle, and flake off as you polish. If you decide to burn shine - make sure you polish the boot normally, shortly after, in an attempt to add some moisture back to the polish to keep the cooked layer from flaking off.

I have also seen horror stories of what "quick-shine" tips can do to boots. Mop'n'Glo, or similar products tend to make a real polish less effective - Future layers of polish rub off. I've seen people try things to perma-shine their shoes such as placing Saran-wrap on the boot then melting it in an oven at low heat (saran wrap will get "run" in it like a stocking). Melting hard plastic such as plexiglass onto the boot (the polish shattered). Don't be stupid. Real men do the hard work required.

Old Paratrooper · 1 year ago

Try using the "clear" kiwi polish for that good mirror finish. I'd forgotten about the panty hose thing. That's a good way to tighten up the shine quickly when you don't want to devote 30-60 minutes to the whole operation. Excellent article!

Former Sgt of Marines · 1 year ago

In the provided pictures above, does everyone see the light tan and white area where the top of the boot meets the soles. It is around the edges where the stiching holds the top of the boot to the soles......... This is called "DIRT." A good scrubbing of the boots and applying of edge dressing or wax to this area will make it black and have a better overall appearance. If you are going to spit shine your shoes to look good, then look good everall inside of just 50%. That dirt around the edges of these boots outway the spit shine that is there. Not trying to knock the poster of this, because he does explain it right, but I think maybe about 5-6 more coats of wax is needed. This looks like it is only about 60% complete. Not that good of a shine. However, this is the correct way to spitshine. Just needs a little more attention to detail.

Former Sgt of Marines · 1 year ago

He was better than you because he was in the Marines. You were satisfied with "Good Enough" because you were in the Navy. !!!!!!!

Jeremy Longfellow · 1 year ago

Im a MA in the Navy and I shine my boots every night with Kiwi Parade gloss, brown T-shirt, spit and lighter method. There is no quick and easy way to shine a boot. Just takes a little effort and elbow grease. Using the brush method is for those who are in it for the "good enough" approach. Put a good base coat on heat it with a lighter (not letting the flame sit in spot or touch the boot) then spit, re apply polish and repeat until you get the desired shine :)

Jim · 1 year ago

Incidentally, should you ever need to totally *ruin* your nice shiny shoes, Sterno...yes, Sterno, the heat source for campers...got all over my shoes this morning and they are duller than I've ever seen.

Cadet 1st LT Johnson · 12 months ago

Well,Your method works excelent,But heres what i found to work better

YOU WILL NEED:Black kiwi shoe polish,a lighter,Old t shirt cut into 12"x12" squares.And of course, Your shoes/boots.

1.Apply 1-3 coats of polish to the toe of your boot/shoe for now.
2.Use lighter to go over polish and melt it into the shoe,Not to long,Just enough(repeat steps 1 and 2 twice)
3.Use the old t shirt (1 or 2 fingers,I use 1) and touch it in the polish,VERY SMALL AMOUNT.
4.spit onto the middle of the part of the shoe you just took the lighter too.
5.Using small uniform circles,Move outward from your spit with the t shirt with the polish on it.
6.Spit more if nescacary,Repeat the process several times until satisfied.(took me about 6-8 repeats of steps 3-6)
Thanks for your time :)

Allstar · 11 months ago

Now this is a useful article for a young man in the 21st century. Good advice, thanks!

Paul Trow · 11 months ago

Loathed as I am to agree with a Life Guard. ;)
Paul Edwards is correct with his cleaning methods.
My career is somewhat similar to his except I served in the Blues & Royals.
I also worked as a Butler for Lord Mountbatten s Grandson the future Lord Mountbatten. Small world.
I do however still beeswax and polish on a daily basis as I provide a service by post. shoe shine on-line. It is very popular with the British military who spend more time with bullets than bulling these days.
Proof is in the pudding so feel free to visit my site and view the examples of my recent work.
I also have a tips page where you can download my free guide to shiny footwear and guide to beeswaxing amongst other goodies.
I also give advice which is always free.
Nice to see there are people out there that still like to keep their kit in good order.
the_butler.
Making stuff shine since 79.

Mike · 9 months ago

When I went to boot-camp, USN, everyone worked on their boots and shoes trying to get them nice an shinny. Then a old timer walked in after ours seeing us all working on our boots, but he had a mirror shine on his, his suggestion... tampons. We went to the px/bx that week for toothpaste, and cleared the whole place out of all their tampons. The ultra tight cotton provided us with shiniest shoes in town; except for that old salt who let us in on his tip.